Use this appliance installation checklist before delivery, renovation, or a service visit to confirm measurements, clearances, utility connections, delivery access, and first-run tests. It is designed to be reused for refrigerators, dishwashers, ranges, washers, dryers, and air conditioners, while leaving code-sensitive decisions to the appliance manual and qualified professionals.
Overview
A successful installation starts before the appliance arrives. A product can fit the cabinet opening but still fail to clear a doorway, connect to the available utilities, open fully, or receive the ventilation required by its manufacturer. Delivery teams may also be unable to complete a hookup if the shutoff valve, electrical outlet, drain, vent, or mounting hardware is missing or inaccessible.
Keep the product page, installation manual, order confirmation, and model number together. Installation requirements vary by model, even within the same appliance category. The manufacturer’s instructions should take priority over general guidance, particularly for electrical, gas, water, drain, ventilation, refrigerant, and clearance requirements.
Reusable measurement template
- Appliance model: ______________________________
- Required appliance width: _____________________
- Required appliance height: ____________________
- Required appliance depth: _____________________
- Available opening width: ______________________
- Available opening height: _____________________
- Available depth to wall or obstruction: _______
- Side, top, rear, and front clearances: ________
- Door or lid swing space: ______________________
- Delivery path width and height: ______________
- Utility type and location: ____________________
- Installation service included? Yes / No / Confirm
- Old appliance removal included? Yes / No / Confirm
Measure the opening at several points rather than relying on one measurement. Walls, flooring, trim, countertops, and cabinets may not be perfectly square. Record the smallest usable measurement and compare it with the installation diagram, not only the headline dimensions on a product listing.
Checklist by scenario
Every appliance delivery
- Confirm the exact model, finish, configuration, and required accessories.
- Read the installation section before moving or disconnecting the old appliance.
- Measure the appliance opening, surrounding clearances, and delivery route.
- Check stairs, elevators, gates, low ceilings, tight turns, and narrow doorways.
- Remove obstacles, secure pets, protect vulnerable flooring, and clear the work area.
- Confirm whether delivery includes unpacking, leveling, hookup, testing, old-appliance removal, and packaging removal.
- Check whether the retailer requires existing utilities to be ready before the installer arrives.
- Inspect the carton and appliance for visible damage before signing, following the retailer’s documentation procedure.
Refrigerator or freezer
- Measure width, height, depth, hinge-side clearance, and the space needed for doors and drawers to open.
- Check whether the doors can be reversed and whether that work must be completed before placement.
- Confirm the required electrical outlet location and that the cord will not be pinched.
- If the model has an ice maker or water dispenser, verify the water-line type, shutoff location, and connection requirements.
- Check rear and side ventilation clearances in the manufacturer’s diagram.
- Plan how the appliance will be leveled without blocking doors, drawers, vents, or access panels.
After installation, confirm that the refrigerator is stable, doors seal evenly, water connections remain dry, and the ice or water feature operates only after the manual’s initial-use steps are complete.
Dishwasher
- Measure the opening between cabinets, including height from the finished floor to the underside of the countertop.
- Confirm that the new unit’s depth, door panel, and handle will not interfere with adjacent cabinets or walkways.
- Locate the water supply, drain connection, and electrical supply according to the installation diagram.
- Check whether a high loop, air gap, junction box, power cord, mounting brackets, or other parts are required for the model and local installation.
- Protect the floor and countertop while removing the old unit and sliding in the new one.
Run a short test cycle or the manufacturer’s recommended test procedure. Look underneath and around the door for leaks, confirm that the unit drains, and verify that it is secured and level. For buying context, see this dishwasher comparison guide.
Range, cooktop, or wall oven
- Identify whether the appliance uses electricity, natural gas, propane, or a model-specific connection.
- Match the required circuit, plug, receptacle, or wiring arrangement to the installation manual and existing home setup.
- For gas appliances, confirm that the shutoff and connector arrangement are appropriate and have the work completed by a qualified professional when required.
- Measure the opening, countertop cutout, backsplash area, hood clearance, and door swing.
- Check whether an anti-tip device or other securing hardware is specified.
- Confirm ventilation requirements for the cooking surface and any hood or downdraft system.
Test burners, heating elements, oven functions, controls, and the clock only after installation is complete. Do not bypass a safety device or use an appliance with a damaged cord, gas odor, unstable body, or incomplete connection.
Washer
- Measure the laundry opening and the full path to it, including closet doors and turns.
- Confirm hot and cold water supply locations, shutoff access, drain height, and electrical outlet placement.
- Remove shipping bolts, braces, or packing materials exactly as instructed before operating the machine.
- Use the correct drain hose arrangement and avoid kinks or loose connections.
- Level all feet and check that the machine does not rock.
Run the recommended initial cycle. Watch the supply hoses, drain, door or lid seal, and floor for leaks. A washer that shakes excessively should be stopped and leveled before regular use.
Dryer
- Confirm whether the dryer is electric, gas, vented, or a ventless model.
- Match the electrical supply and outlet to the model requirements; do not assume an existing cord or receptacle is compatible.
- For vented dryers, inspect the vent route, termination, length, bends, and approved materials against the manual.
- For gas models, confirm the shutoff and connector requirements and use qualified installation help where appropriate.
- Check stacking or pedestal compatibility if the dryer will be paired with a washer.
Run a brief heated or drying test as allowed by the manual. Confirm that the drum turns, the controls respond, airflow is present where applicable, and no gas odor, unusual noise, or excessive vibration occurs.
Room air conditioner or other air-care equipment
- Measure the window, wall opening, floor space, or mounting location required by the model.
- Confirm the electrical outlet and circuit requirements, including whether an extension cord is prohibited.
- Check outdoor airflow, drainage, support brackets, and weather sealing for window or through-wall units.
- For portable units, plan the exhaust route and condensate management before unpacking.
- For split or permanently installed systems, use appropriately qualified HVAC installation services rather than improvising refrigerant or electrical work.
After installation, test the operating modes, airflow, controls, drainage, and any connected-app setup. Keep the manual and model number for future filter, part, and service searches.
What to double-check
Clearance is more than fit
Check the space needed to open doors, remove filters, pull out racks, clean behind the unit, and reach shutoffs. A refrigerator may fit between cabinets but fail to open fully. A dishwasher may fit under a counter but collide with a drawer. A dryer may fit in a closet but lack the ventilation or service access required by its manual.
Utilities and accessories
List every connection before delivery: power, gas, water, drain, vent, exhaust, and network access if the appliance is connected. Confirm which hoses, cords, valves, brackets, trim pieces, filters, or adapters are included. Do not select replacement appliance parts by appearance alone; record the complete model number and verify compatibility. The model-number parts guide explains a reliable lookup process.
Installation responsibility
Separate tasks into three groups: work you can safely prepare, work included by the retailer, and work requiring a qualified trade professional. Electrical changes, gas connections, structural mounting, refrigerant work, and changes controlled by local rules deserve particular care. Ask for a written description of what the installation service includes before delivery day.
First-run records
Keep the delivery date, model and serial numbers, installer details, photos of connections, and notes from the first test. These records can make a warranty or repair conversation easier. If a problem appears, stop using the appliance when continued operation could cause water damage, fire risk, electrical danger, gas exposure, or further mechanical damage.
Common mistakes
- Measuring only the appliance: Include the opening, trim, doors, handles, hinges, and delivery route.
- Ignoring finished-floor height: New flooring can change the available opening for dishwashers, ranges, and built-in units.
- Assuming connections are universal: Cords, hoses, gas fittings, vents, and water filters may vary by model.
- Leaving shipping hardware installed: Washers and some other appliances can be damaged or operate poorly if transport materials are not removed as directed.
- Blocking access: Do not place an appliance where its shutoff, filter, drain, or service panel cannot be reached.
- Skipping the leak test: Check water connections during and after the first cycle, not only when the installer leaves.
- Relying on a product listing alone: Use the model-specific installation manual for clearances, utilities, and mounting instructions.
- Discarding documentation too soon: Save manuals, receipts, serial numbers, and installation photos until the appliance has completed its initial operating period.
When to revisit
Use this checklist whenever you buy, move, remodel, replace, or reconnect an appliance. Recheck it before seasonal planning cycles, especially before cooling or heating equipment is put back into service. Review the manufacturer’s current installation manual whenever the model changes, a room is renovated, flooring or cabinetry is replaced, or a utility connection is modified.
It is also worth revisiting after a leak, electrical issue, unusual vibration, ventilation change, or failed installation appointment. Retailer delivery and installation policies can change, so confirm included services and preparation requirements shortly before delivery rather than relying on an older order or a previous appliance purchase.
For ongoing ownership, pair this installation record with an appliance maintenance checklist. Before you act, print or copy the measurement template, fill in the model-specific requirements, photograph the connections, and complete the first-run test. If the appliance cannot be safely connected, leveled, ventilated, or tested, pause the installation and arrange qualified help.